26″ Road Bike Cycling Sport Racing 50cm 18 Speed 700CC Aluminum W/ Disc Brake

Description

Store category Sign Up Now ! You may additionally like 26″ Road Bike Cycling Sport Racing 50cm 18 Speed 700CC Aluminum W/ Disc Brake Product Description Frame Size: 50cmSpecificationsGenderUnisexCategoryRoad BikeMaterialAluminium AlloyBike Speed18 SpeedBicycle Wheel Size26 Inch/700CCBody MaterialAluminiumCassetteFW51,14-28TShift LeverSHIMANO TX30Rear DerailleurSHIMANO TZ50Front DerailleurMICROSHIFT FD-52Fork TypeNon-DampingPedals TypeAluminiumRider Weight (KG)165-185Bike length (CM)169Wheel MaterialAluminium AlloyFork MaterialAluminium AlloyIs there a suspension fork?NoBrake systemBB5 Disc BrakeIf Folding or NotNot 6061 Aluminium Alloy Frame – Sport oversized frame with rear suspensionComfortable Geometry – Allows easy and effective steeringFront & Rear Disc Brake Calipers – Powerful, progressive braking perfect for all weather conditionsBraking System – Powerful and progressivePaint Layers – Three layers of paint provide the frame with lasting protectionAluminium Alloy Pedals – Sturdy and light weight with Large surface area for more powerNew ERGO FIT sport saddle for extra added comfortAluminium Alloy Quick Release – Easy to adjust saddle positioningLearn More About This ProductQ:How to Assemble a Bicycle?A:Before Getting Started – Please remove all the cardboard protective wrapping from unassembled bike.1.Frame 2. Stem 3. Handlebar 4.Thumb Shifter 5.Brake Handle 6.Fork 7.Hub Brake 8.Front Wheel 9.Front Axle 10.Shift Cable 11.Bottom Bracket 12.Chainwheel 13.Pedal 14.Front Derailleur 15.Rear Wheel 16.Foot Improve 17.Rear Derailleur 18.Rear Axle 19.Brake Cable 20.Seat Post 21.Saddle1.Frame 2. Stem 3. Handlebar 4.Thumb Shifter 5.Brake Handle 6.Fork 7.Hub Brake 8.Front Wheel 9.Front Axle 10.Bottom Bracket 11.Chainwheel 12.Pedal 13. Rear Wheel 14.Foot Wheel 15.Rear Derailleur 16.Rear Axle 17.Seat Post 18.Saddle 19.Folding LeverB:Seat Installation.A) Straddle the assembled bicycle with feet shoulder width apart and flat on the ground.There must be at least 2.5cm of clearance between the highest part of the top tube and crotch of the rider with tires fully inflated.B) Tighten the seat clamp bolts of the seat post following the torque specifications for the seat post. Do not over tighten for the hex sockets will strip.C) Loosen the seat clamp nuts and rotate the Seat into riding position as shown in Image 2.D) Apply a small amount of grease on the seat post.Insert the seat post in the seat tube.Put the seat post fully through the seat clamp as shown in Image 3.E) Tighten the seat clamp so that the seat is secured in the seat post as shown in image 4.If the seat clamp has a nut on each side, tighten both nuts equally (the pressure must be consistent on both sides).Caution: To prevent the seat from loosening and conceivable cause loss of control, the “MIN-IN” (minimum insertion) mark on the seat post must be below the top of the seat tube as shown in Image 5.C:Handlebar InstallationA) Unscrew the stem cover with the hex tool.B) Open the stem cover to place the handlebar with the bike handles facing the frame of the bike. Make sure the back gears are on the right side and the front gears are on the left side. Additionally, make sure it is centered before tightening. Tighten bolts slightly and measure the distance from each end of the grip to the center of the handlebar. If it needs adjustment, do so at this time before.C) Insert Stem into Stem Tube. To prevent steering system from losing control, the minimum Insertion Mark on the Stem must be below top of the Stem Tube as shown on Image 6.D) Straddle the front wheel between your legs, hold the handlebar and adjust the handlebar at 90-degree angle with the frame as shown on Image 7.E) Tighten the stem bolts securely as shown on Image 8.D: Pedal InstallationA) The right pedal is marked “R” and the left pedal is marked “L” as shown on Image 9.B) The right pedal has counter clockwise threads. Make sure to tighten it in a clockwise direction. The left pedal has clockwise threads. To secure, tighten it in a counter clockwise direction as shown on Image 10.C) Add a small amount of grease on the thread to ensure that it is not stripped and easy to screw.D) Turn the pedal into the crank arm.Make sure the threads of each pedal are fully screwed into the crank arm.E) Fully tighten the pedals with a wrench as shown on image 11.E: Front Wheel InstallationA) Set the front wheel into the front fork.B) Make sure the quick release lever is on the disc side.C) Move the disk side of the wheel to the left side.D) Undo the quick release lever slightly to make room for to secure on drop out.E) Make sure to center the wheel and roll towards the bike frame without touching the sides of the front fork or brake pads.F) Rotate the quick release lever (tighten) and lock.G) Rotate the wheel to make sure that it is balanced. If not, please take the bike to a technician to balance the wheel.H) Attach the front wheel with the axle nuts.I) Tighten the axle nuts at both sides.F: Tensity of the ChainMake sure that the chain swings at an amplitude of approximately 15mm by adjusting the screws of the chain.G:Kickstand InstallationA) Select an area on the frame near the rear wheel on the left hand side.B) Clean with a damp cloth and let it air dry.C) Cut a piece of electrical tape so that it can go around the frame at least twice. This will ensure that all the parts make a close connection and the bike does not get scratched.D) Tighten the Hex bolts.H: Adjust the DerailleurA) Adjust the front derailleur in advance.a. Adjust Screw C to make the derailleur parallel with the chainwheel; ensure to leave 3-5 mm space from cusps as shown on Image 1 and 2.b. Push the derailleur lever to the forefront position as shown on Image 3.c. Put the chain on the largest freewheel and little crankset position.d.Adjust Screw A to set the chain in the derailleur.If the derailleur is not able to return to the previous position, then loosen the shift cables and loosen Screw A. After, pull the shift cable upwards to loosen it; follow by tightening Screw A.e. Push the derailleur lever towards the rear of the bike; then put the chain on the large crankset and small freewheel. Adjust Screw B to set the chain in the middle of the derailleur.B) Adjust the Rear Derailleura. Tighten Screw A clockwise if the chain slips out of the small freewheel.b. Tighten Screw B clockwise if the chain slips out of the large freewheel.c. Chain jamming may be as a result of the cable or the derailleur being too loose. Do not completely tighten the lever at this stage.d. Loosening of the derailleur screw may result in the chain returning to the small freewheel. Tighten the lever as shown on Image 4.e. If shifting is difficult from the small freewheel to the large freewheel, it may be as a result of the cable freewheel being too tight. Loosen the derailleur by adjusting Screw C. Make sure that the guide wheel is aligned properly to every freewheel as shown on Image 5.I:Intelligent Display Assembly & AdjustmentSome models are equipped with an intelligent display unit.Intelligent Display System consists of three components:a. A Intelligent Display Screenb. A Speed Meterc. A Sensor Magnet”A) Insert batteries as shown on Image 1:a. Remove the battery coverb. Put in two AAA batteriesc. Close and secure the battery cover.B) Install the Display System as on Image 2.Place the bottom half of the device’s mount on the bike’s handlebar; adjust the position to your preference. Place the top half of the mount. Secure with a hex key – M6.C) Insert Batteries as on Image 3:a.Insert a CR2032 battery (positive electrode upward).b.Close and secure the battery cover with a coin/key in a clockwise direction. (Please do not force tightening).D) Install the Speed Meter and Sensor Magnet as on Image 4:a. From the front fork, place the sensor facing frontwards with wires going up the fork. Secure with a hex key – M4.b. Wrap a zip wire around the cable and secure towards the back. Do not over tighten for you’re going to damage the wire. Clip excess plastic.c. Take the wire up the fork and secure towards the top.d. Begin wrapping the wire around the brake cable housing with a little slack to avoid damage (wrap lightly).e. Make sure there is slack on the wire before it reaches the handlebar. (Do not stretch.)f. At the top of the brake cable housing, secure the wire on the brake cable with a zip wire. Clip excess zip wire.g. Connect wires to computer.h. Install the magnet to the spokes; line up with sensor. It should be approximately 1-5 mm away from the magnet. Make sure the magnet does not hit the sensor.J:No Thread Headset Installation.A) Top cap (A) is used to adjust the headset.B) Pinch bolt B and C are used to adjust the bike head. To adjust the headset through top cap A, please loosen pinch bolt B and hex bolt C first. Then tighten the top cap (A). Once adjusted, secure pinch bolts B & C.K:Tools Needed.A) Hex Tool Kit.B) Measuring Tape.C) Wrench.D) Electrical Tape.E) Bike Grease.In the last, If you’ll be able to’t assemble well with yourself, For better assembly and performance, please have a professional assemble your bike or contact our customer service. Payment Delivery details Return About us Contact us Payment 1. Payment must be received within 7 days from the date of purchase. If the buyer won’t pay within 7 days, We will be able to close this transaction. 2. We will be able to send the item after the e-check has cleard ,if the buyer is paying through Paypal using eCheck. Orders will be processed instantly and dispatched in same day normally, so we do NOT accept any Email/Message note after you placed orders. 3. We accept PayPal only. Delivery details 1. We don’t seem to be responsible for any custom duty or import tax. 2. We only ship to confirmed Ebay addresses. Your Ebay address must match your Shipping address. 3. Items are generally shipped in 1-3 business day after your payment has been cleared. 4. If you wish to change you order ,example the shipping address / color / size ,please leave a message in the paypal notes when you make payment. Return 1. Return shipping should be paid by buyer. 2. You have 30 days to contact us for returning it from the date you received it. If this item is in your possession more than 30 days, it is regarded as as used and We will be able to not issue you any refund or replacement. 3. All returned items must be in the original packaging and you must provide us with tracking number, specific reason for the returns and your eBay ID. 4. We will be able to refund you upon receipt of the item in its original condition ( but NOT include the shipping fee we paid for the item), after both Buyer and Seller cancel the transaction from eBay. Or you may have a replacement. About us 1. If you are dissatisfied for any reason, please contact us before leave negative/neutral feedback.Our Customer Service Department will answer your emails within 24 hours. Contact us 1.Our Worktime is Monday to Friday (9:00-18:00).

Reviews

There are no reviews yet.

Be the first to review “26″ Road Bike Cycling Sport Racing 50cm 18 Speed 700CC Aluminum W/ Disc Brake”

Your email address will not be published. Required fields are marked *